Age old questions abound, which could cause a constant series of debates. Which is better, Chevrolet and Ford, Coors and Budweiser, winter or summer?
Ask some guys who is the best alarm system, wired or wireless, and certainly some opinions strong enough to support one or the other for receiving. Battlelines drawn in length, will try to the bottom of this problem are clearly divided.
Wired alarm panels are less expensive than Wi-plates, but are more difficult toEasy to install. Keep this in mind if you plan to do the installation yourself. A facility average home with a hard-wired system takes about 12-16 hours. A typical wireless installation takes less than 4 hours.
Another consideration is that some types of construction are suitable for cable installation, and others require the use of wires. Normally, all alarms are wired for commercial, residential, and a large percentage of plantsUse the Internet without wires.
Even if you buy a wireless alarm panel, most systems require that some of the wired devices. These typically include power transformer, electrical grounding, telephone and all keyboards / fitting stations, and audible alarms. There are some exceptions to this, some of the latest all-in-one units currently available, the basic unit, the station arm and audible alarm to take a unit thatIt connects to your existing phone sockets.
The main difference between a hard-wired and wireless alarm panel, as all connected devices to communicate with system security. A jury will require a wired network a thread for each "zone" or the device on the system, while a wireless system, a radio frequency, using the "zone" or devices that are connected with communication.
While a normal electrical circuit is a parallel circuit, a typical hard-wiredAlarm circuit is a 2-wire loop with NC End of line supervision is commonly referred to as a series circuit.
A series circuit allows power flow back from the alarm panel, provides a wire from the alarm device and initiate the alarm panel. When the power is interrupted, the group recorded a fault on the line / area. End of line (EOL) resistors are added to the track, so that the alarm panel to monitor the condition of the area for earth fault,Short circuits and open lines or cut.
Different devices can be closed, as a rule, to a single area are connected with the connection of devices installed in series with the EOL resistor at the last device in line. In this way, the entire circuit will be completely controlled by the panel is the last device in line.
If the wireless alarm systems first appeared on the market, were not the most reliable system. Most of them are not used under the supervision wireless transmitterseach of the field devices. A non-controlled wireless alarm transmitter, a signal only "one way" to the receiver alarm panel when activated.
For example, if a door or window is opened, the transmitter sends a wireless signal. The alarm panel should receive the signal and activate the appropriate zone. The transmitter would not be a signal if the door or window was closed, so that the receiver area was reset itself after a fewSeconds. With a non-controlled wireless system that you can actually open the arm with a door or window wide, without knowing it.
Most of the new alarm systems use a redundant connection for bidirectional fully supervised wireless two-way communication between the sender and the recipient of the alarm panel. With fully supervised wireless alarm panel can have the real-time status of the door or window. If a door is open, there will be the fault zoneIs closed to the door.
Most of the early wireless systems were very limited in the treatment systems. Have this dip switches with binary address (below), Member distinguish between the points of the system.
He was fine, if the wireless system was installed and commissioned, but what happens if your neighbor installed the same type of system? If the motion detector close to the recipient the garage door, the alarm would off every time he went to his house. As you can imagine, this could be some major problems to solve very difficult.
Modern wireless systems using the serial numbers of binary codes or other proprietary technologies ensure that only the stations are listed in the panel will be received by the alarm system. When you do your research and to supervise the purchase of a good, reliable alarm system, you should never worry about your neighbor> Transmitters crediting the alarm system.
Another problem with the older non-monitored systems is that you do not know when the batteries are low or in the channels must be replaced. The only way to ensure that they work, must be tested regularly.
Even the most sophisticated wireless alarm panels are useless if the transmitter battery died, so wireless monitors are programmed panels so that each controlRemote stations, at least once every 24 hours. If the transmitter has a low battery, the keyboard / arming station immediately inform the condition of difficulty.
Regularly with a portable system of security that should always make the system performance. The range of wireless products for the environment and structure that is interested in be installed. In addition, the offer may be influenced by environmentalEquipment as electrical interference or direction of the transmitter in relation to the recipient.
Who is the winner of this topic? Well, according to Underwriters Laboratory (UL) using the method safe and reliable installation, equipment wired to end of line (EOL) 1 or 2-resistance surveillance. In fact, the installation UL for the federal government and other high security require that all plants to be protected2-wired with complete line of surveillance of resistance.
Not to say that wireless systems are an inferior product. In fact, fully monitored systems offer very good protection, which is perfect for 90% of existing plants at the appropriate time.
If you prefer a wireless alarm system into consideration, be warned, there are still sold and installed today's systems that are not controlled, so as to ensure that whatever system you are planning to offer a complete wirelessSupervision.
If you opt for a hard-wired alarm, please be sure, that the system is installed with the supervisors to line resistance. To make installation faster and easier by some installers in the alarm panel, the resistances are held and not at the end of the line.
Although this method provides for the supervision of the area for earth fault, it means no protection for a short, direct or, worse yet, someone spliced the wire and shorted themtogether, in essence, close the loop, the panel will not see the area to open or close.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น